Microtek MS4 Uživatelský manuál Strana 1

Conference Projectorswww.microtek.comUser's ManualMS4 DLP Projector

Connectors view ITEM LABEL DESCRIPTION SEE PAGE: 1. Audio-in Connect the audio cable (supplied) from the input device 11 2. RS-232 Reserve

Bottom view ITEM LABEL DESCRIPTION SEE PAGE: 1. Projection lamp cover Remove when changing lamp 24 2. Height adjuster 3. Side foot Adjust

Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-rescent light

ITEM LABEL DESCRIPTION SEE PAGE: 1. Laser Use as on-screen pointer. DO NOT POINT IN EYES. 2. IR transmitter Transmits signals to projector 3.

Remote Control Operating Range The remote control uses infrared transm ission to control the projector. It is not necessary to point the remote direc

SETUP AND OPERATION Inserting the Remote Control Battery 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow

Connecting Input Devices A PC or notebook computer as well as video devices can be connected to the projector at the same time. Video devices includ

Starting and Shutting down the Projector 1. Connect the power cord to the projec-tor. Connect the other end to a wall outlet. The Power LED and Lam

Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy.

Adjust the Zoom, Focus and Keystone 1. Use the Image -focus con-trol (on the projector only) to sharpen the projected image . 2. Use the Image -

Copyright This publication, including all photographs, illustrations and software, is protected under international copy-right laws, with all rights

Adjusting the Volume 1. Press the Volume +/- but-tons on the projector or the remote control. The volume control ap-pears on the display. 2. Use

ON-SCREEN DISPLAY MENU SETTINGS On-Screen Display Menu Controls The projector has an On-Screen Display (OSD) that lets you make image adjustments an

Setting the OSD Language You may want to reference the OSD on your projector while reading this section. Set the OSD lan-guage to your preference be

Main Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Main menu. Press the cursor button to move up and d

Setup Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Setup menu. Press the cursor button to move up an

Config Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Config menu. Press the cursor button to move up

Utility Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Utility menu. Press the cursor button to move

Language Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Lan-guage menu. Press the cursor button to mo

Status Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Status menu. Press the cursor button to move up

MAINTENANCE AND SECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a c

Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following boxes are used in this manua

3. Remove the two screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the mod-ule handle to remove the lamp module. 6. R

Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the Menu button to op

Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure tro uble-free operation. Warning: 1. Be sure to turn off an

Cleaning the Case Refer to the following to clean the projector case. 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm

TROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If

LED Error Messages LED STATUS/ NUMBER OF FLASHES DESCRIPTION Flashing Lamp not ready —do not press the power button 1 Power fan error 2 Lamp f

Problem: The image is flat with no contrast 1. Adjust the Contrast setting on the Main menu of the OSD. Problem: The color of the projected imag

trying to fix the problem. The information may be useful to the service personnel. Return the projector to the place you purchased it.

SPECIFICATIONS Specifications Display type TI DMD 0.55-inch x 1, 12 degrees, DDR DLP Resolution SVGA 800 x 600 Native Color 16.7 Million (24-bit

Input/output connectors DVI-I PC USB Composite video (RCAx1) Video S-Video (Mini-DIN) Audio Mini-jack Service/upgrades RS-232 Security Kensington

Remote Control The remote control has a laser for pointing out items on a screen. DANGER: Do not point the laser in the eyes. Doing so can damage th

Projection Distance V.S. Projection Size L Projection distanceScreen heighScreen WidthABCD Max. Screen Size Min. Screen Size Projec-tion Distanc

Timing Charts The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. Ta

Dimensions 28.0 cm (11.02 in.)9 .7 c m (3.8 1 in.) 21.7 cm (8.54 in.)

REGULATORY COMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pur-suant to Part

Table of contents GETTING STARTED...

GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: PowerMenuKeystoneAutoEnterSource

Views of Projector Parts Front-right view ITEM LABEL DESCRIPTION SEE PAGE: 1. Lens/focus turn the lens to focus 14 2. IR receiver Receiv

Top view ITEM LABEL DESCRIPTION SEE PAGE: 1. Image-focus control 14 2. Zoom Enlarge or shrink the projected image 14 3. Power Turns the

Top view —OSD buttons and LEDs ITEM LABEL DESCRIPTION SEE PAGE: Green Unit is powered on and working correctly Off Unit is powered off 1. Pow